In other words, at most, we would have 3 units of 2.5 inches and 1 of 3.5 inches, or 2 of 2.5 inches and 2 others on 3.5 inches.
This tower is ready to mount basic ATX, micro -Atx and Mini -it plates. And, given its size, where we have to be careful, it is in the size of some of its components:
- Processor dissipator: maximum height 166 mm.
- GPU: Longitud Máxima 330 mm.
- PSU: Maximum size 180 mm.
For the rest, it is compatible with liquid refrigerations, able to install a 120 mm radiator at the rear, or one of the 240 mm at the top. As for the fans, we can install one of the 120 mm at the rear (it is included), 2 at the top of 120 or 140 mm (two of the 120 mm with argments are included), and 2 of 120 mm at the bottom of the tower (20 mm are included with 20 mm with argb of inverted leaves).
Finally, the Tower Connections panel brings us, in addition to the ignition button, a Gen2 type C of 3.2 USB, a USB 3.0 port and an audio socket.
External analysis
This tower is available in a simple cardboard box, although smaller than that of other models, which is appreciated, because we can move it better. At the front of the box, we have a photo of the tower in question, while we find all the parts that form it.


We can also see the specifications and characteristics of the tower on the side.


We open the box and take out the tower. This is well protected by enlarged and plastic polystyrene to avoid damage during packaging and transport. In addition to the box, we find accessories, such as Bay for Hard Drives, an assembly manual, two fans and all the screws.
The tower, as we can see from the first moment, is much smaller than the other models. He has the whole front and a glass side, and is designed to watch the RGB from the inside.
By already entering detail, the front of the tower is a semi-talented tempered glass, leaving a grid to ventilate at the bottom.
In the upper part, we find the ignition button, the connection panel and a magnetic grid that we can remove to clean or mount the fans.


The left side of the tower is also completely covered with tempered glass.
And the lower part has a ventilation rack, just like the front.
At the rear, we find the fan, the hole for the connection panel of the motherboard, the PCI berries and the hollow font.
The right side is a whole steel plate.
And finally, below, we have a grid that helps us ventilate the tower and the 4 legs on which the tower is maintained.
Internal analysis
The interior of the tower is quite traditional and conservative, with nothing to emphasize. We can access it by removing the front and the side of the tower. And, having no vertical support in this corner, the amplitude of the assembly is multiplied.
The first thing we find inside the tower, subject by a bridle, are two additional fans who include us and that we can place, for example, at the bottom of the tower.
These fans are a 120r argb, XPG, and stand out for a 9 raw design and argb lighting.
We can also remove the rear panel to access the rear of the tower. This only hides the cables and a pipe which is really quite poor.


We can also find the two spaces for 2.5 -inch units in this back.
In addition, from behind, we can access the hole for food. It is a fairly wide hole, so we can use it to hide the cables we don't need.


Food is supported on rubber transplants, which helps reduce unwanted vibrations. And also, if we will put another SSD or another hard drive, we can place the bay there.
The wiring that comes from the base with the tower is very basic and does not go beyond the cables of the three fans that are mounted and those of the IO panel of the Torre.
The IO panel cables of the Torre are the same that we can find in any other tower. We can see electric pins, USB cables and HD audio cables.
Fans, as we can see, are quite simple. These are XPG brands and are standard to put fresh air inside (repair them that the two superiors have inverted blades, so they put air).
As we can see, although the possibilities of rear pipes are very simple, the tower is very prepared to mount the source at the rear and eliminate the cables we need at the front, able to make a very clean assembly.
Assembly of a PC on the Adate XPG Invader x Mini
We liked the assembly of the tower. Although it is smaller than the other towers on the market, the interior is very wide (with regard to) and the absence of the front left axle helps a lot to mount the components.
As usual, the first thing we did was placed the power supply. We used a modular source, so we only connected the cables we needed, being able to have all the wiring much more organized.
After the fountain, we set up the motherboard. We chose an ATX plaque, which we placed in its place, then tighten the screws. We had no complications, although it is true that the right space is perceptible.
With the source and the plate mounted, the next step was cooled. We can choose between the cooling of the liquid or an air dissipator. Unless we have a small dissipator, it is better to opt for a liquid of 120 or 240 mm.


We must also connect the graphics card before continuing with the wiring. Thus, we can choose the best way to remove the cables and connect them so that the assembly is as clean as possible.
And, with everything else mounted, we just have to connect the cables. What gave us the most problems for space, was the CPU cables. The rest, we had no problem. If it is your case, remove the fan at the top to have more space and when you have connected the CPU cables, move it again.


Once we already have all the wiring and ready, we put the cables a little so that they are not seen, we keep them on the back and voila. Our tour is mounted and ready to work.
Conclusion, is it worth it?
The truth is that this Adata tower surprised us a lot. Accustomed to seeing very large laps and more than 10 kg of weight, we met a much smaller model than normal, both high (although less) and, above all, long, which is especially intended to climb on a desktop.
Despite its small size, XPG opted for an open design which, by removing the side and the front leaves us a very wide space to be able to assemble without any problem. As we said, the only problem we found was the connection of CPU power cables. But, no matter that, we have not encountered absolutely no other problem.
The lighting he offers us is right, it is a normal argb that we can control from the motherboard itself, which can be good for certain users, but somewhat limited, with regard to other options, for those looking for maximum personalization.


If you were to put a handicap, it would certainly be its size, because there are many components (large liquid refrigerations or large graphics cards) that we will not be able to install, directly because they do not enter. But, if not, we are faced with an excellent tower, perfect for those who do not have excessively large components, bet on a classic dissipation system and have no space for a conventional tower.
For all these reasons, we have decided to give this mini Tower of Adata Xpg Invader X Mini Tower of Adata our Gold Award, highlighting, in particular, its design.


Table of Contents



















