Of course, not everyone has Aquaero, but it's way more than recommended, which is compelling in terms of which organs, which will allow us to improve the temperatures, health and wear of our liquid cooling components.
For this reason and with a pure mind, we will start based on the fact that we have a liquid cooling system, a body temperature sensor, and one Aqua Computer product to open an Aquasuite license, if possible Aquaero logically, because without it we cannot use the function described in this article.
Aqua Computer Aquasuite: the world's top liquid cooling control software
Aquasuite is a control software specifically designed for the products of Aqua Computer, where everything is focused on its flaga Aquaero product. As they have connected both the pump and the fans respectively independent channels, either directly or through a splitter (do not mix the fans with the pump / s), we will know the steps to be performed The effectiveness of the stems is based on water temperature.
What about the temperature of the water? Because it's a way to avoid that the shock of sudden changes in our genes. The processor or graphics card is always changing the temperature, so if we focus on the temperature of the sensor on the physical or software sensors, our fans and pump will have a steady rise and continuous RPM.
This forces the motors and shafts to great resistance in a short period of time, so the sensor option in the water is very effective, as it is very difficult to heat a liquid. The idea is that as water temperature rises changes are gradually increasing, while lowering RPM and doing the same.
Aquasuite allows us this and much more, especially with regard to the control of the same nerve channel, so to speak, let's know how to achieve it.
The first step is to go to the sidebar of Aquasuite and select ours Aquaero, once inside we will go to the section Administrators.
This will open up this panel, where, as we can see, we have already created two perfectly equal curves for our two elements.
The next step is to select the «rightadd«. We will click on it to select the type of control we want to create.
In our case we will build the curvature control by several points, so we choose Curve curve
When done, our defined curve will be displayed on the screen, which, as we can see, has no selected sensor or controllers. To start with the process of creating a curve, first, you need to click on «+» Inside the data source.
We will turn on the number of sensors that automatically detect Aquasuite. Here we see our two sensors controlling the two loops and the virtual sensor we have configured in the suite itself. All of this is configured from the Sensors section, but we must do it before selecting one of these in this section.
In our case we will choose a CPU water sensor, because it is a the sensation of the body which we added to the loop.
The next step is to always have a temperature readout curve to choose what we want to control with that data. This we select and then click the button The results
In this case and since we have configured everything on the fan section, we can choose on the LEDs to turn on or off to warn us about the temperature at any time, to relay or power out automatically.
In our case we will choose one of the four parameters we have configured. Here we have to emphasize that we can add them all at once, two, three or one, in full reach.
What we should know is The results we select cannot be selected with a different curve, that is, if we select a CPU pump, this source cannot be selected with a different curve, because to do so (because the option will be available in simple logic) will move from one curve to another.
We already have a well-made cart, now we have to prepare it, in which to show its possibilities we will add more releases.
As we can see, there are two ways to prepare a curve: automatic and manual. Default mode is not quite as automated as it is, because we will provide parameters manually, but it will enable you to create a curve type automatically and continuously, depending on our needs.
Hand mode is a common mode where each base point is assigned two values: temperature and% control / power (depending on whether we have PWM or 3 pins)
As we can see, the manual mode has three sets: the temperature at each point of the curve, the percentage of load and the temperature of the starting point of the curve. This type of mode is useful when we want a sudden escape of RPM at a certain temperature, or when a certain temperature we want the system to gain or lose performance at its pump or RPM because we see that it helps partial temperatures, be it CPU, GPU or mother
Normal mode to use the default, because we provide a lower temperature and a higher value, where we can change the base curve by moving the navigation bar left or right.
As for the amount of energy, the most common is to save a small amount 0%, this is done because previously in the fan section we have to calculate what minimum support amount they convert, the same pump case.
As a practical example of previous configuration and for understanding, we will use the configuration of the bomb and CPU circle followers.
As we can see at the tap, less power is available at 50% at 6 volts, as D5 and DDC do not fall below that percentage. PWM control and associated RPM are selected to mark the range.
Same case for our 8 Corsair ML 120 Pro, except in this case the percentage and RPM change. So, back to the dress, 0% of this represents 30% and 50% we've just seen, since Fans adjustment is more like over the curve.
What we get with this system is that the fans and the pump never stop, but when the water is cold save as little time as possible (calculated based on trial and error before curve is created).
This we will have excellent performance, great sound and minimal wear potential for our equipment and water supplies.
